CONMOLY
Balancing loss, size, mass and flexibility in an RF interconnect
Begin with the signal path and installation, then compare cable constructions against the same requirements. A useful RF interconnect selection keeps loss, available space, mass and movement in one review. Selecting only the smallest diameter, lowest listed mass or a family name leaves important questions unanswered.
For an RF assembly manufacturer, the review includes the connector and termination process. For a test-system integrator, it also includes the switch or instrument port, fixture, routing and acceptance of the complete path.
Set the electrical and mechanical boundaries
Record the required impedance and frequency range, finished length, connector part numbers and reference interfaces. Set the insertion-loss and return-loss requirements, and any phase criteria that matter to the application. Identify which connectors, adaptors and fixture sections are included.
Mark the routing envelope, connector access, strain-relief space and movement on a sketch. Distinguish a fixed installation from a cable repositioned during use or disconnected between measurements. These are different evaluation conditions.
Use published dimensions and mass to screen candidates
The following examples are reproduced from CONMOLY's basic RF product data. They identify four constructions for initial review; they do not rank their RF performance.
| Model | Centre-conductor construction | Published overall diameter (mm) | Published mass (g/m) |
|---|---|---|---|
| CM-COAX-PS-F-OD3P60 | Solid silver-plated | 3.6 | 32 |
| CM-COAX-PS-F-OD4P82 | Solid silver-plated | 4.82 | 53 |
| CM-COAX-PS-UF-OD3P60 | Stranded silver-plated | 3.6 | 31 |
| CM-COAX-PS-LW-OD3P60 | Solid silver-plated copper-clad aluminium | 3.60 ± 0.10 | ≤23 |
The flexible and ultra-flexible families list low-density PTFE insulation. The lightweight OD3P60 model lists ePTFE / LD-PTFE dielectric and FEP as its default jacket selection. Retain the complete model and construction in any comparison.
The mass limit for the lightweight model retains its inequality. The other mass entries are reproduced as published; they are not relabelled as guaranteed maxima. The dimensional entries likewise retain their original precision and tolerance.
Use the current basic specifications for the flexible, ultra-flexible and lightweight families to identify the relevant construction. A similar outer diameter is not proof of connector compatibility or interchangeable cable preparation.
Compare loss on a defined basis
Before accepting a loss comparison, identify the frequency or frequency range, sample length, temperature, connector inclusion and whether the value is nominal, typical or a specified limit. If a result is length-normalised, retain the stated basis and method. Do not turn it into a complete assembly result without an applicable model or measurement.
Keep insertion loss separate from return loss. Rohde & Schwarz's RF fundamentals material presents transmission and reflection as separate VNA measurements and describes mismatches at interfaces along the signal path. This supports reviewing the full arrangement rather than inferring its RF result from a cable dimension. RF fundamentals: components and measurements
The basic model entries used here do not establish a complete assembly loss curve or a quantitative phase-stability result. Keep those comparison fields open until configuration-specific evidence is available. Neither the largest cable nor the lightest construction can be declared the electrical winner from this table.
Check what the size and mass change means for installation
For each candidate, check the connector drawing, centre-conductor construction, dielectric and shield dimensions, preparation lengths and termination method. Include supports and strain relief in the proposed assembly arrangement.
If a lighter construction is being considered, review its conductor and shield materials as part of that process. If a different diameter is proposed, review connector access and the actual route. Compare finished configurations when the project requirement applies to an assembly rather than cable per unit length.
Define the flexibility requirement
Ask whether the requirement concerns installation bending, repeated movement, phase change while repositioned, or recovery after returning to the original route. Define the bend geometry, motion and electrical acceptance accordingly.
CM-COAX-PS-LW-OD3P60 lists a minimum bend radius of 17.5 mm. That entry is not a repeated-flex life rating and is not assigned here to the other models. The words “flexible” and “ultra-flexible” do not supply a cycle count or a phase-change limit.
For a phase-sensitive path, record the bend or temperature conditions and the measurement reference. A low initial loss and a satisfactory fit do not by themselves establish the required phase behaviour.
For the related selection steps, see phase stability under bending and temperature.
Make the trade-off explicit
| Selection issue | Evidence needed before choosing |
|---|---|
| Loss requirement | Applicable frequency/length/configuration result and limit type |
| Diameter and space | Published dimensions, controlled connector preparation and routing review |
| Mass | Correctly labelled cable data and the intended finished configuration |
| Flexibility or movement | Defined geometry, motion and electrical acceptance |
| Phase behaviour | Separate bend/temperature evaluation under agreed conditions |
| Supply scope | Confirmed cable/assembly form, quantity and timing |
Keep mandatory requirements separate from preferences. If more than one candidate meets the required conditions, compare the value of the remaining differences with the termination, evaluation and supply work needed to introduce it. Leave an unresolved performance item visible rather than assigning a score that assumes it passes.
For the related selection steps, see comparable quotations and sample validation.
Prepare a configuration review
Provide the signal-path sketch, required frequency range, length, connectors, route, mass constraint and movement conditions. Add the loss and phase criteria and any applicable records for the current arrangement. This gives the review a defined comparison basis; supply terms and sample arrangements require separate confirmation.
Discuss configuration requirements
Frequently Asked Questions
- Why should loss, size, mass and flexibility be reviewed together for an RF interconnect?
- Selecting only the smallest diameter, lowest listed mass or a single family name leaves electrical and installation trade-offs unresolved. Reviewing frequency range, finished length, attenuation, routing envelope, connectors and movement together yields a comparable shortlist.
- What requirements should be recorded before comparing RF cable candidates?
- Record the target impedance, operating frequency range, finished assembly length, connector interfaces, insertion-loss and return-loss limits, any phase criteria, routing space, mass budget and whether the cable is fixed or repositioned during use.
- Can published cable dimensions and mass replace finished-assembly evaluation?
- No. Published cable dimensions and mass help screen candidate constructions, while connector interfaces, termination process, fixture sections and complete-path performance must be confirmed for the actual assembly.
