CONMOLY
Defining signal and environmental requirements for differential-pair and bus cables
A useful cable enquiry describes the signal path and the environment in which it must operate. For a differential-pair or bus interconnect, those descriptions need to refer to the same cable, connectors, length and installation. The term “harsh environment” alone does not define the required construction or acceptance.
Start with a link sketch and a requirement list. Identify the items that are mandatory, the conditions that are still being investigated and the evidence needed for a configuration decision.
Identify the interface and the complete path
State the actual signalling interface or communication protocol, required data rate, number of pairs, installed length and direction of communication. Provide connector part numbers, pin assignment and relevant equipment-interface documentation. Include driver/receiver and termination requirements where applicable.
Mark the equipment, cable sections, connectors, adaptors, feedthroughs and fixture or device under test on the sketch. State which of these elements is included in the acceptance requirement. Keep the complete model identifier and any suffix with the proposed construction.
In a temperature-chamber application, distinguish the signal cable connected to the device under test from a control cable outside the chamber. Record the exposed sections and interfaces explicitly. A description of the chamber does not identify the cable's actual exposure.
Keep the construction with the electrical entries
CONMOLY's published data include the following two distinct examples:
- CM-LVDS-PP-ND-AWG24-S01: a parallel pair with two 24 AWG silver-plated copper conductors, ePTFE / PTFE core insulation, LD-PTFE overall insulation, two braided shield layers and a transparent FEP jacket. It has no drain wire.
- CM-CAT6A-4P-AWG26: four pairs of 26 AWG silver-plated copper conductors, ePTFE / PTFE insulation, individual aluminium-foil pair shields, an overall silver-plated copper braid and a blue FEP jacket.
| Published entry | CM-LVDS-PP-ND-AWG24-S01 | CM-CAT6A-4P-AWG26 |
|---|---|---|
| Differential impedance | 100 ± 10 Ω | 100 ± 10 Ω |
| Capacitance | ≤43 pF/m | 43 pF/m, nominal |
| Propagation delay | ≤4.5 ns/m | 4.3 ns/m, nominal |
| Operating temperature | −55 to +200 °C | −55 to +200 °C |
The shared impedance entry does not make these constructions interchangeable. Preserve the upper limits for the LVDS entries and the nominal qualifiers for Cat6A. The operating-temperature entries belong to the specified cable constructions; they do not establish protocol performance across that range.
Specify electrical acceptance and its method
Identify the limits required by the actual interface and project. Where relevant, include impedance, loss, return loss, crosstalk, conductor resistance, propagation delay and delay matching. State the measured conductors or pairs, units, length, test frequency or range, temperature and connector inclusion.
Keep propagation delay separate from delay skew and protocol data rate. A value expressed per unit length does not supply a complete-link acceptance result. If the definition, limit direction or applicable method is unresolved, keep that item open for engineering review.
For shielded constructions, define shield termination and bonding in the connector arrangement. A cable without a drain wire still needs an identified shield-termination design. Include the cable-preparation drawing and strain-relief arrangement when reviewing the intended assembly.
Define environmental exposure as a set of conditions
Record the minimum and maximum temperature, continuous operation or short-duration exposure, duration and any required cycling profile. Identify where temperature is measured and which cable and termination sections are exposed.
Add the actual installation and movement requirements: routing space, bend geometry, vibration or repeated motion where applicable, supports and mechanical restraint. Define the electrical and mechanical criteria needed during or after those conditions.
If the application includes fluids, pressure, vacuum, cleaning or other special exposure, specify the medium, conditions and required evidence separately. A PTFE material name or operating-temperature entry does not establish those additional properties for the cable assembly.
For the related selection steps, see material versus finished-cable temperature.
Connect the signal and environmental evaluations
Agree which measurements are needed before exposure, during exposure or after return to the reference condition. Keep the sample identifiers, cable and connector versions, installed length and method with every result.
A room-condition cable measurement and a complete-link test during temperature exposure have different scopes. Decide what each existing record supports before deciding whether an additional evaluation is needed. Retain any unresolved link or environmental requirement rather than treating an incomplete record as a pass.
| Requirement group | Information to provide |
|---|---|
| Signal and interface | Actual interface, data rate, pair count, length and pin assignment |
| Construction | Full cable model/revision, connectors, shield termination and preparation drawing |
| Electrical acceptance | Limits, units, measured pairs, methods and reference interfaces |
| Temperature | Range, exposure type, duration/profile and exposed sections |
| Installation | Route, supports, bend, motion and restraint |
| Other environments | Applicable media/conditions and required evidence |
| Evaluation record | Sample IDs, before/during/after stages, results and unresolved items |
Prepare a configuration review
Provide the sketch and requirement list with the proposed cable identifiers and any existing records. Mark unknown fields for clarification. This creates a basis for reviewing the specific signal and environment together. Available supply forms, quantities and delivery arrangements require separate commercial confirmation.
For the related selection steps, see align quotations with the sample evaluation.
Discuss configuration requirements
Frequently Asked Questions
- Why is describing an application simply as “harsh environment” insufficient for signal cable selection?
- “Harsh environment” does not specify the actual thermal, mechanical, chemical, moisture or EMI exposures, nor does it define the electrical acceptance method. Both signal-path requirements and specific environmental conditions must be linked to the same cable construction.
- What signal-path details should be included in a differential-pair or bus cable enquiry?
- Include the signalling interface or protocol, data rate, pair count, installed length, connector part numbers, pin assignments, termination requirements and a link sketch showing every section covered by acceptance criteria.
- Why must the complete model identifier and suffix be kept with electrical entries?
- Different constructions or suffixes within the same family can differ in shielding, geometry, materials or listed temperature entries, so keeping the complete code avoids mixing incompatible parameters.
