CONMOLY
PTFE material temperature and finished-cable operating temperature
A temperature statement is useful only when its scope is clear. A polymer supplier's service-temperature statement describes the material product covered by that source. A cable operating-temperature specification applies to a defined cable construction. A connectorised assembly needs a review that includes the connectors and terminations.
Keep these levels separate when selecting a PTFE-insulated cable. A material reference can support the review of a construction, but it cannot by itself establish the operating range of a finished cable or test path.
What a material temperature statement tells you
Chemours' PTFE 62 X product information lists a service temperature up to 260 °C for that resin grade. The document identifies a fine-powder resin and is marked C-10127 (2/16). This is a grade-specific material reference, not a finished-cable specification. Chemours PTFE 62 X product information
Chemours' FEP resin overview lists high service temperatures up to 200 °C for the resin products described there. That material statement does not set the rating of every FEP-jacketed cable. Chemours FEP resin overview
These examples are third-party material references. They do not identify the resin grades used in the CONMOLY models below, and they are not evidence that those models have completed testing at the quoted material temperatures. A melting-point entry, processing temperature and service-temperature statement should also retain their separate meanings when reading material documentation.
Identify what the cable specification actually covers
Keep the complete model, drawing revision and construction with the temperature entry. Review the dielectric, conductor and plating, shields, jacket and any other materials present in that construction. A shared material name is not enough to transfer a temperature range from one model to another.
The following model-specific entries come from CONMOLY's basic product data. They are cable specifications, not batch-level test reports or proof of full-channel performance at every temperature.
| Cable model | Published jacket entry | Published operating temperature |
|---|---|---|
| CM-COAX-PS-LW-OD3P60 | FEP by default; alternatives according to the configuration | −55 to +165 °C |
| CM-LVDS-PP-ND-AWG24-S01 | Transparent FEP | −55 to +200 °C |
| CM-CAT6A-4P-AWG26 | Blue FEP | −55 to +200 °C |
The operating-temperature entries remain attached to their stated cable constructions. If an alternative jacket is proposed, confirm the corresponding construction and temperature specification. The common PTFE or FEP material names do not explain, replace or increase these model-specific limits.
If a basic specification omits a temperature range, request the applicable configuration specification. Do not borrow a figure from a nearby model or another product in the same family.
Add the connectors and installation
For a finished assembly, identify connector part numbers, cable-preparation dimensions, termination details and any strain-relief materials. Record which parts are exposed to the temperature requirement. An environmental chamber may contain part of the cable while other interfaces remain outside it.
Use component information to screen the configuration, then review evidence applicable to the complete arrangement. Taking the lowest number from a set of component datasheets does not demonstrate that the assembled product has met the required environmental and electrical acceptance.
| Information level | What it should identify | What still needs review |
|---|---|---|
| Material reference | Supplier, grade, property and stated conditions | Applicability to the actual processed material and construction |
| Cable specification | Complete model, revision, construction and operating conditions | Applicable configuration and evaluation evidence |
| Sample test result | Sample/batch, method, exposure and measured result | Which requirement and production configuration it supports |
| Assembly application | Cable, connectors, termination and exposed sections | Acceptance of the complete installed arrangement |
Define continuous operation, short exposure and cycling
Specify the lower and upper temperature, continuous operation or short-duration exposure, exposure time, number of cycles where relevant, and the surrounding environment. Include any electrical loading, movement or other concurrent condition required by the application.
Keep the stated test purpose with its result. A thermal-shock or short-exposure result cannot on its own establish a continuous operating-temperature rating. A successful test applies within its actual configuration, method and acceptance conditions; record those before deciding whether it supports a new requirement.
Specify the signal result as well as the temperature
Define what the cable or link must do during or after exposure. An RF project may require loss, return-loss or phase-change limits under specified conditions. A differential-data project needs the actual interface and complete-link acceptance requirements.
Temperature and phase change are separate requirements. An operating-temperature entry does not provide a phase-change curve. Likewise, a cable impedance or delay entry does not demonstrate that a particular protocol has been validated across the temperature range. Match any result to the cable, length, connectors, reference interfaces and exposure conditions actually evaluated.
For the related selection steps, see separate bend and temperature phase evaluations.
Build a complete configuration record
For a high-temperature requirement, prepare the model or controlled drawing, full material construction, connector/termination identifiers, temperature profile and exposure conditions, acceptance limits, sample/batch identification and applicable original records. Review the technical scope and the commercial supply scope separately.
A request reaching 260 °C needs that complete configuration review. Neither the resin example above nor the 165 °C and 200 °C cable entries establish a CONMOLY finished-cable or assembly rating at 260 °C.
For an initial review, provide the temperature profile, exposed sections, signal requirements and intended interfaces. This defines the information needed to assess a specific configuration without substituting a material headline for a cable specification.
For the related selection steps, see signal and environment requirements for data cables.
Discuss configuration requirements
Frequently Asked Questions
- Can a PTFE resin service-temperature rating be used directly as a finished cable operating temperature?
- No. A resin datasheet describes the polymer material product itself, whereas finished-cable operating temperature applies to a defined cable construction including conductor plating, shield and jacket; connectorised assemblies must also include connector and termination limits.
- What is the difference between material temperature, cable temperature and assembly temperature?
- Material temperature refers to a specific resin grade reference; cable temperature applies to a defined complete cable construction; assembly temperature additionally accounts for connectors, terminations and installation conditions.
- Besides temperature endpoints, what thermal details should a cable specification define?
- Distinguish continuous operation, short-term exposure and temperature cycling, and state the electrical or mechanical signal criteria required before, during or after thermal exposure.
